
測量表面或體電阻
設計的初衷是用於測量平坦包裝材料,這套獨特的可擕式測試裝置可配合現行業界標準測量幾乎任何平坦材料的表面和體電阻。
這些測量內容包括:根據ANSI/ESD STM11.11測量表面電阻、根據ANSI/ESD STM11.12測量體電阻、根據ASTM D-257測量表面和體電阻率。
注意:ANSI/ESD標準用於需要靜電放電控制的材料,而ASTM D-257則用於評估絕緣材料在電氣配置和電力的應用。

搭配電阻計使用
PRF-911同心圓是一種精縮的測量裝置,專用與Prostat電阻測量儀器搭配使用,比如PRS-801電阻測量系統、PRS-812高阻計、以及PAS-853B電阻稽核系統。
同心圓是一個用於計算表面電阻率和體電阻率的重要工具。例如:將表面電阻測量值(ohms)乘以10可獲得表面電阻率(ohms/square)。

測量ESD袋
其小巧的尺寸可容許它嵌入小尺寸並且有彈性的包材內,例如ESD防護袋,而不需切割包材。

保持持續性接觸
PRF-911內嵌一個彈簧式自動對準的中心電極。在測量過程中,此特徵可輔助強化電極表面的高導電性橡膠和待測材料持續接觸。
這種設計可降低裝置頻繁校正和中心對準的需求。

雙面測試板適用任一測量
PTB-920雙面測試板的絕緣面用來測量依據S11.11的表面電阻值,附貼在一起的不銹鋼面則用於測量體電阻率。
直徑4英吋的不銹鋼測試板包括一個香蕉插孔,可用於在體電阻測量過程中的儀錶連接。

寬廣量程範圍、精確測量效能
PRF-911可以精準測量從小於100 ohms (<1.0x102 ohms)到大於1.0x1012 Ohms (>1.0x1013 ohms/square)的量程範圍。這種配置可接到任何儀錶的參考接地或大地接地,以降低測量時來自於外圍靜電場和靜電荷的干擾。
規格
CONCENTRIC RING DIMENSIONS
Inner electrode disc (D1) outside diameter: 1.2 inches (3.05cm) – Spring Loaded
counter pressure approximately 2 lb., ± 2 ounces (0.82 Kilograms, ± 0.06 kg)
Outer electrode ring (D2) inside diameter: 2.25 inches (5.72cm) Width 0.125 inches (0.32cm)
counter pressure approximately 2 lb., ± 2 ounces (0.82 Kilograms, ± 0.06 kg)
Outer electrode ring (D2) inside diameter: 2.25 inches (5.72cm) Width 0.125 inches (0.32cm)
ALIGNEMENT
5.0x105 ± 1% Ohms @100 volts per ANSI/ESD STM11.11 for Surface Measurements
5.0x105 ± 2% Ohms @10 volts
5.0x105 ± 1% Ohms @100 volts for Volume Resistivity Measurement
5.0x105 ± 2% Ohms @10 volts
5.0x105 ± 2% Ohms @10 volts
5.0x105 ± 1% Ohms @100 volts for Volume Resistivity Measurement
5.0x105 ± 2% Ohms @10 volts
VOLUME RESISTIVITY CORRECTION
6.9 cm2 Total D1 Contact Area. Allows for D1 mounting screw head.
FIXTURE WEIGHT
1.8 lb (0.82 kg) without BNC/Banana adapter or connections.
CONNECTIONS
Fixture installed BNC for Inner Disc (D1) connection, and fixture assembly ground; dual BNC/Banana plug adapter supplied.
Fixture installed standard banana receptacle for Outer Ring (D2) connection.
Fixture installed standard banana receptacle for Outer Ring (D2) connection.
DUAL TEST BED
Diameter: 4.0 inches (10.16 cm). Lamination of 1⁄8 inch acrylic plastic and ¼ inch stainless steel, or aluminum plate.
POWER
Not Applicable. The fixture and test bed are used in conjunction with the PRS-801 Resistance System and test leads.