PFK-105 Ionization Test Set
PFK-105 Ionization Test Set
Perfect Kit for Testing and Balancing Ionizers
  • Includes a FIeld Meter, Charge Plate Monitor, Charging Source and Decay Timer
  • Balance Ionizers per ANSI/ESD SP3.3 Periodic Verification
  • Measure Ionizer Decay time as per ANSI/ESD S3.1 and ANSI/ESD SP3.3.
  • Measure Body Voltage Generation and Decay
  • Measure decay times for ionizers and materials
  • Evaluate Ionizers and Packaging Materials
  • Includes a fixture to hold the PFM-711A, CPM-720A and PDT-740B as one
Static Field Meter
Meter for Testing of Electrostatic Fields
The hand-held PFM-711A Fieldmeter is an instrument used to perform static surveys and polarity on objects with accuracy of ±2% at ambient conditions (23ºC and 30%Rh). This stabilized chopper can be used in environments with a presence of ionization without drifting. The Hold button allows the field meter to hold the measurement for easy recording. It also features automatic polarity indication, low battery indicator, high and low ranges, distance ranging lights for accurate and repeatable measurements, manual zero control and a ground snap. The PFM-711A includes two ranges of operation:

  • 0 to 1,999V in 1 Volt increments with <±2% error
  • 0 to 20,000V in 10 Volt increments with <±5% error up to 5kV

The PFM-711A can be used with a X-Y plotter, any analog data-recording devices, or the PGA-710B Autoanalysis System. The analog output provides a 1 volt output corresponding to 10kV, which is independent of the selected meter range and indication.

Measure Ionizer Performance
Charge Plate Monitor allowing you to Measure Ionizers
The CPM-720A Charge Plate Monitor is an accessory that attaches to the PFM-711A Field Meter. When attached, the system will allow to balance ionizers per ANSI/ESD SP3.3, voltage or charge generation and voltage suppression analysis.
Charging the Charge Plate Monitor
Charge It Up!
The PCS-730 ±1 kV Charging Source is used to charge the CPM-720A Charge Plate Monitor to ±1,000 volts to measure ionizer decay time as required by both ANSI/ESD S3.1 and ANSI/ESD SP3.3.

The PFM-711A Field Meter, the CPM-720A Charge Plate Monitor and the PCS-730 Charging Source are match calibrated to work together for accurate and efficient auditing.

Static Decay Rate and Static Dissipation Testing
Measuring Material Decay Time
The PDT-740B Static Decay Timer is typical of Prostat’s innovative technology and support of Professional ESD Control Managers and Auditors.

This unique accessory is designed to measure the decay time of ionizers from ±1,000 volts to less than 100 volts in accordance with ESD Association’s Ionization Standard ANSI/ESD STM3.1, and measure material decay time to less than 50 volts and less than 10 volts.

Perform Decay and Balance Test of Ionization Equipment
A Helping Hand for Ionizer Analysis!
This fixture is designed to easily hold your PFM-711A Field Meter, your CPM-720A Charge Plate Monitor your PDT-740B Static Decay Timer. Lightweight, this instrument holder will facilitate balancing your ionizer, by holding all instruments in 1 hand.

Technical Specifications

PFM-711A FIELD METER

METER DISPLAY

3-1/2 digit Liquid Crystal Display with 0.4" digit height. Automatic polarity, HOLD and LOW BATTERY indicators.

OUTPUT

Analog signal output and 30 inch two conductor cable provided. ± 10.0KV meter reading equals ± 1.0 volts output.

RANGE

High Range 0 V to ± 19.99 KV; least significant digit indicates tens of volts at one inch distance.
Low Range 0 V to ± 1,999 V; least significant digit indicates 1 volt at one inch distance.
Measures higher voltages at greater distances, e.g., at two inches double indicated voltage, at four inches multiply indicated voltage by four.

RANGE LIGHTS

Red "Bulls Eye" at one inch distance

ACCURACY & ENVIRONMENT

± 2% at ambient conditions ( 23ºC and 30% Rh).
± 5% at 0 - 50ºC and 0 - 85% Rh (non-condensing).
Accuracy unaffected by the presence of air ionization.

RESPONSE

Digital display updates three (3) times per second.
Analog Output Time Constant: Either Range 0.1 sec.
Display Time Constants: High Range 0.2 sec; Low Range 2.0 sec

CONTROLS

Three position slide switch: KV/INCH - OFF - V/INCH
Sample/HOLD push button, and ZERO adjust knob.

GROUNDING

Meter circuit grounded through the conductive case and 10 mm snap fastener mounted on back of case.

POWER

9 VDC alkaline battery. Battery life minimum 40 hours.

DIMENSIONS

2.4" wide x 4.2" long x .9" deep (1.3" deep with zero knob and snap fastener).

WEIGHT

5 ounces, with battery

PCS-730 CHARGING SOURCE

INPUT POWER

9 Volt Alkaline Battery. Battery life in excess of 40 hours continuous operation.

OUTPUT

± 1,000 volts DC Minimum, Current limited to less than 1 Microamp.

OUTPUT

Female banana jack provided with mating contact rod.

GROUNDING

10mm female snap fastener on rear of case. Note that wand must be installed and unit grounded for proper operation.

SIZE

2.5"W x 4"L (4.2"L with jack) x 1.5"D (1.8"D with switch and snap)

WEIGHT

6 oz (with battery)

CPM-720A CHARGE PLATE ASSEMBLY

ISOLATED PLATE

Stainless Steel parallel plates, 3.25 inches square. Auxiliary female jack installed.

CAPACITANCE

Plate Capacitance 10 picofarads (pF) ± 1 pF
Note: Plate capacitance is 15.8 pF when mounted to PFM-711A Filed Meter

RANGE

0 to ± 6 KV at a plate separation of 0.60 inch.

ACCURACY

± 2% at 1,000 volts. Calibration adjustment screw provided.

GROUNDING

Through conductive case and snap fastener of Model PFM-711A.

SIZE

3.25"W x 3.25"L x .9"D (1.0"D with jack).

WEIGHT

8 oz.

PDT-740B STATIC DECAY TIMER

CONTROLS

OFF-ON Cut Off Voltage, 10, 50 and 100 Volts (Selects Voltage to stop timing)

INDOCATORS

Green LED:
Decay Cycle Ready > ± 1kV, CPM voltage > ± 1,000 volts

Red LED:
Timing in Progress, CPM voltage decay timing activated LOBAT displayed when battery voltage <6.0 volts

DISPLAY:

Liquid Crystal Display (LCD) displays elapsed decay time from ± 1,000 volts to selected Cut Off voltage in seconds and tenths of a second (00.0)

POLARITY

Automatically senses Positive & Negative voltage references

ZERO & RESET

Automatically Resets Timer and Display to 00.0 when CPM voltage > ± 1kV. Reset indicated when Green LED Decay Cycle Ready LED is ON.

RESPONSE

Approximately 200 milliseconds in combination with the CPM-720 and PFM-711A

TIMING RANGE

From 0.2 to 159.9 seconds

TIMING SETPOINTS

Reset when voltage input 100mv ± 2mv (1,000 Field Meter Volts ± 20V)
Cut Off Voltage @ 100 V: 10mv ± 0.2mv (100 Field Meter Volts ± 2V)
Cut Off Voltage @ 50 V: 5mv ± 0.2mv (50 Field Meter Volts ± 2V)
Cut Off Voltage @ 10 V: 1mv ± 0.2mv (10 Field Meter Volts ± 2V)

ACCURACY

Typically < ± 5%

POWER

One (1) standard 9-volt battery, PROCELL, Eveready #216 (NEDA 1604, JIS 006P, IEC 6F22)Eveready #216

BATTERY LIFE

>40 hours typical

DIMENSIONS

4.50 inches x 2.75 inches x 1.0 inches

WEIGHT

6.5 oz. (184 gm)

PFK-100H INSTRUMENT HOLDER

CONSTRUCTION

Aluminum

DIMENSIONS

8.25 in x 3.0 in x 1.0 in (20.96 cm x 7.62 cm x 2.54 cm)

WEIGHT

5.4 oz (153g)

Downloads

User Manuals

Filename
Language
Release Date
Size


English
2015-02-02
1,111 KB

English
2007-03-19
8,599 KB

English
2015-11-25
738 KB

Videos

No videos available for this product.